About This

 

 

Nearly everybody will have their own individual idea when it comes to How to Install a Bathtub: Install an Acrylic Tub and Tub Surround.

Mounting a bathtub isn't precisely brain surgery, yet it does call for strong plumbing, woodworking, and also occasionally, tiling skills. Changing an old bathtub with a new one is also a moderately difficult project. If the old tub is readily accessible, the project can move speedily; if you have to open a wall to get rid of the old bathtub and also place the brand-new bath tub, the job is a lot harder. In either situation, the job is within a home handyman's abilities, although you will certainly require an assistant to leave the old tub and embeded in the brand-new one. Ensure you have qualified yourself for the job and also fit trying it. Instead of employing a professional to take over a halfway-completed project, it is far better to take into consideration utilizing one before you begin. Chances are you might require an expert plumber to make tube connections.
This article will certainly aid you set up a new bathtub in your washroom if you have actually already purchased a new bathtub and also do not need to change the setup of your previous water supply pipelines.
Your tools and product list ought to comprise the following:

 

• New Bath tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Flexible Wrench


• Putty Knife


• Screwdriver


• Cold Knife


• Measuring tape


• Pipeline Caps


 

Removing Old Taps

If you need to replace old taps with new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, activate the faucets to drain any type of water remaining in the system. The process of getting rid of the existing faucets can be fairly troublesome because of the restricted access that is often the instance.
Make use of a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that attaches the supply pipelines to the taps. Have a cloth all set for the continuing to be water that will certainly come from the pipes. As soon as the supply pipelines have been removed, make use of the very same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning throughout this procedure. When the taps have actually been eliminated, the holes in the bath/basin will need to be cleaned up of any type of old sealing substance.
Before moving on to fit the brand-new taps, compare the pipeline connections on the old taps to the brand-new taps. If the old faucets are longer than the brand-new taps, after that a shank adapter is needed for the new faucets to fit.

 

 

Fitting New Taps

If the tails of the brand-new taps are plastic, after that you will need a plastic adapter to avoid damages to the string. One end of the connector fits on the plastic tail of the faucet as well as the other end supplies a connection to the current supply pipes.
If you need to fit a monobloc, after that you will call for decreasing couplers, which attaches the 10mm pipe of the monobloc to the standard 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the tap and the sink. Protect the tap in place with the manufacturer supplied backnut. Once the faucet is securely in position, the supply pipelines can be linked to the tails of the faucets. The taps can either be attached by using corrugated copper piping or with regular tap ports. The former type needs to be connected to the faucet ends initially, tightening up only by hand. The supply pipelines can later be linked to the various other end. Tighten both ends with a spanner after both ends have actually been connected.

 

 

Setting up the Bath tub

Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are valuable in equally spreading the weight of the tub over the location of the boards as opposed to focusing all the weight onto four tiny points.
The next objective is to ensure that the tub is leveled all round. This can be attained by checking the spirit level as well as readjusting the feet on the bathtub up until the level reads level.
To mount taps, fit the bottom of the outermost adaptable tap port to the ideal supply pipe by making a compression join; then do the very same for the various other tap.
Switch on the water system and also check all joints and new pipework for leakages and also tighten them if necessary. Fill the tub as well as additionally examine the overflow outlet and the typical electrical outlet for leakages.
Ultimately, fix the bath paneling as explained in the maker's instruction manual. Tiling and sealing around the tub must wait till the bath tub has actually been used at least once as this will settle it into its final setting.

 

 

Getting ready for the Installment

To start with, the sustaining structure provided with the bathroom needs to be fitted (if required) according to the manufacturer's instructions. Next, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to make sure that if the tap comes with a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bathroom, it is additionally reasonable to fit a sustaining plate under the faucets system to avoid stress on the tub.
Fit the versatile tap connectors to the bottom of the two faucets making use of 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the electrical outlet via the hole in the bathroom. Utilize the nut supplied by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipeline to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the supplied washers.
Attach the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a comparable manner.The bath should now prepare to be suited its final position.

 

 

Tiling Around the Tub

In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to break a rigid seal, creating the water to pass through the wall surface between the bath and also the tiling, causing complications with dampness and also possible leaks to the ceiling listed below.
You can select from a range of coloured sealants to assimilate your fixtures and installations. They are offered in tubes and cartridges, and can sealing gaps approximately a width of 3mm (1/8 inch). If you have a larger void to fill up, you can fill it with spins of soaked paper or soft rope. Keep in mind to always load the tub with water before securing, to enable the movement experienced when the bathtub is in usage. The sealant can crack rather early if you do not take into account this motion before securing.
Additionally, ceramic coving or quadrant tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to size, are additionally quickly available on the marketplace. It is advisable to fit the floor tiles using waterproof or waterproof glue and cement.

 

How to Install or Replace a Bathtub

 

Find Your Dimensions

 

The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.

After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?

 

Disconnect the Water Supply and Drain Assembly

 

Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.

Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.

Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.

 

Cut Out the Old Tub

 

After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.

Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.

Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.

 

Install the New Tub

 

Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.

Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.

Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.

When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.

 

Secure the Tub

 

After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.

Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.

Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.

Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.

https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/

 

I was shown that write-up on Tools You Need to Install a New Bathtub through an acquaintance on a different blog. Those who enjoyed our article if you please make sure you remember to pass it around. I praise you for your time. Don't hesitate to check our blog back soon.

Top Article